Hp designjet 5500 service manual

Open the Top Cover and pull the Carriage out along the Printer to the position shown. Push in the 2 retaining clips either side of the Printhead Tube Connector. Push the button to release the Printhead Tubes in the Carriage. Release the Retaining Clip by pulling it away from the holding brackets. The complete assembly can now be removed by sliding the Ink Cartridge Connector out from the rear of the Left Hand Cover. The Front Panel displays the message shown.

Wait about 60 seconds for the next instruction. Remove the Setup Printheads from the Printhead Carriage. The procedure you select depends on the part you want to access. Remove the Back Cover - Refer to Page Remove Electronics Module - Refer to Page Disconnect connector from Ink Leak. Do steps 1 to 5 of the EMC Covers as one assembly procedure. Do steps 1, 2 and 6 of the EMC Covers as one assembly procedure. Remove the 5. Slide the Trailing Cable Guide out of the Carriage. NOTE Take care when removing and inserting these screws as they are easily damaged and not easy to access.

Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Designjet , HP Designjet , service manual Download for 1. Removal and Installation Introduction This chapter is a step by step guide to the removal and installation of the key components in the Printer.

Safety Precautions Safety symbols - Immediately after the table of contents. WARNING Serious shock hazard leading to death or injury may result if you do not take the following precautions: Ensure that the ac power outlet mains has a protective earth ground terminal.

Switch the printer off, and disconnect it from the power source prior to performing any maintenance. Prevent water or other liquids from running onto electrical components or circuits, or through openings in the module. Required Tools The following tools are required to disassemble and repair the Printer. NOTE Detail of hinge mechanism. NOTE 1. Open the Top Cover. Open the door at the back of the Left Hand Cover.

Removal and Installation 4. Disconnect the Air Tube. Removal and Installation 7. Removal and Installation Remove the Left Hand Cover from the Printer.

Switch off the Printer and remove the Power Cord. P24 3. P29 P Raise the Media Lever. Cancel Unsubscribe. Working… Subscribe Subscribed Unsubscribe Free shipping on orders over. Model numbers and ink system type.

With this solution, you can enjoy easy wireless printing from a computer or mobile device while producing prints up to dpi for crisp, outstanding images every time.

HP Designjet Find great deals on eBay for hp designjet printer. HP DesignJet Printer series. Shop for your printer supplies and much more with us today! HP DesignJet large-format professional photo printers offer a wide color gamut, so you can confidently deliver fine detail that satisfies even the most discerning art lover. Find great deals on eBay for parts hp designjet.

Welcome to ManualMachine. Removal and Installation. Mark on Box. Remove the boxes from the top of the main printer box. Figure : Removing top boxes. Remove all eight plastic handles from both sides of the box. Figure : Removing handles. Remove the two packing pieces. Figure : Removing two packing pieces.

Assemble the Stand caution: Do not remove anti-slip material from around the wheels of the printer feet until directed to do so. Begin by attaching the legs to the outside of the cross brace. Figure : Attaching the legs to the outside of the cross brace. Install eight screws into the legs. Figure : Installing screws into the printer legs. Attach the feet into the cross brace with screws. Remember to leave the anti-slip material on.

Figure : Attaching the feet into the cross brace with screws. Position the feet into the leg assembly. Figure : Positioning the feet into the leg assembly.

Check that all screws are fully tightened. Attach the Legs to the Printer Find the handles on the rear of the printer. There must not be any obstruction within three meters of this point. Figure : Arrows pointing to the handles on the rear of the printer. Carefully pull aside the plastic covering and put the legs assembly on the printer. Secure with four screws. Remove the accessories from the accessory boxes, and then replace the polystyrene inside the boxes. Put the two boxes on the floor, and tilt the printer onto the boxes.

Figure : Place the boxes as shown to support the printer. Remove the media rolls and spindle from the shipping container. Figure : Removing media rolls and spindle. Figure : Removing the anti-slip material from the wheels. Install the two stabilizers onto the rear of the feet. Make sure to install both stabilizers. Figure : Installing both stabilizers onto the rear of the feet.

Install the pins into the two stabilizers and secure with the retaining clips. Figure : Installing pins into the stabilizers and securing with retaining clips. Adjust the stabilizer feet so that the wheels do not touch the floor. Figure : Adjusting the stabilizer feet. Remove the Packing Tape and the Desiccant Bag.

Open the window and remove the carriage packing material. Figure : Removing the carriage packing material. Install the pocket on the rear of the printer.

Figure : Installing the pocket. Figure : Loosening the screws to install the take-up reel. Release the clamp on the left-hand assembly by removing the screw.

Figure : Removing the screw and releasing the clamp. Install the left-hand assembly on the loosened screws installed in step 1. Figure : Installing the left-hand assembly. Pull the left-hand assembly down so that it rests securely on the screws. Figure : Pulling the left-hand assembly down to rest securely on the screws.

Install the clamp and secure it with the clamp screw. Figure : Installing the clamp 1 with the clamp screw 2. Install the front of the sensor assembly into the front of the right foot assembly.

Figure : Installing the front of the sensor assembly into the front of the right foot assembly. Slide the sensor clamp firmly up against the right leg, and then secure the sensor clamp with a screw. Figure : Slide the sensor clamp 1 firmly against the right leg 2. Tighten the screw to secure the clamp in place and connect the sensor cable. Figure : Securing the clamp and connecting the sensor cable.

Be sure that the spindle lock is open. Figure : Spindle lock open.